• Always On Vpn Cisco Anyconnect
• Cisco Asa Always On Vpn
• Vpn Anyconnect Download

Topics Map > Networking > Virtual Private Networking (VPN)

IPv6 addresses and headers take up more space in the data packet than IPv4 addresses and headers do. Because of this some users are not able to connect to the VPN at all, and others can connect but can't download files, read email, or do other things that use large data payloads in their data packets. Adjusting the packet MTU to a lower value will make sure that there is enough space in the packet for the larger IPv6 headers.

Microsoft DirectAccess was once touted as the go-to tech for secure remote access connectivity. But now it has a new player in the game: Always On VPN. I am testing AnyConnect's 'always on' feature. The connect failure policy is working as I expected. I thought I would others input. The Automatic VPN policy has been in place for sometime. Trusted - disconnect. Untrusted - connect. At this point, I enable Always On, Allow VPN disconnect and set the failure policy to Open. Download Cisco AnyConnect Secure Mobility Client for Windows & read reviews. The guarantee of Cisco Security. Aug 10, 2020 Likely the single most common complaint about Windows 10 Always On VPN is that device tunnel or user tunnel VPN connections fail to reconnect automatically after a laptop computer wakes from sleep or hibernate. You will find many complaining about this issue and discussing various attempts at resolution on the Microsoft forums.

This only affects customers that connect over IPv6. Cisco's AnyConnect software will always use IPv4 if it is available, so this will mostly affect customers using openconnect, or customers that only have IPv6 (which is rare). The default MTU for wireless and Ethernet is 1500 bytes. When using IPv6, especially if it is being tunneled, you'll need to set it down to between 1380 and 1450 depending on the your setup.

1. If you can't connect at all and your client just times out trying to connect (and is using IPv6 to get to the VPN*), then first check to see if you can ping6 the vpn (unix/Mac OS command is 'ping6 vpn.illinois.edu'). If that doesn't work, this is not the problem.
2. If ping6 worked, then see if you can load the website over IPv6. https://vpn4g-1.gw.illinois.edu (or any of the VPNs). If it loads, this probably isn't the problem. If it loads, and the VPN connects, but then some things don't work, it might be the problem.
3. If ping6 worked, but loading the website did not work, then there is a good chance this is your problem. Please try changing your MTU setting and see if that fixes the issue.

If you think this is the problem you are having, then you need to set your MTU size down to at lest 1450, possibly as low as 1380 to make everything work.
Mac OS:

1. Go to Network settings
2. lick on the interface being used for their network connection, if it is not already selected.
3. Click on the 'Advanced' button.
4. Click on the 'Hardware' tab.
5. Change the 'Configure:' drop down to Manually.
6. Change the 'MTU:' drop down to Custom.
7. Type in 1380, click Okay, and then click Apply.

Windows 7, 8, and 10:

Open a command prompt

1. Click the Windows button on the task bar.
2. Click All Programs.
3. Click Accessories.
4. Right-click on Command Prompt and click Run as administrator.
5. If prompted click the Allow button.

Set the MTU size:

1. Once the Command Prompt window is open follow the steps below to change the MTU size:

   1. Type netsh interface ipv6 show subinterface
   2. Press Enter.
   3. You will see a list of network interfaces.
   4. Type netsh interface ipv6 set subinterface “Local Area Connection” mtu=1450 store=persistent
      You should replace Local Area Connection with the name that appeared in the “Interface” column from steps 1-3.
   5. Press Enter.
   6. Restart you computer and then test again.

   If you still have problems after modifying the MTU repeat the above steps - replacing the numbers 1458 with 1430, or 1380 – restart the computer and test again.

   
   

Linux:

1. In Linux there are multiple ways to do it. Here are two possibilities:
1. If you are using openconnect, use the '-m 'option to specify the MTU like this
1. openconnect -m 1380 -v vpn.illinois.edu
2. Otherwise, after the vpn has connected, adjust the mtu on the tunnel interface that was created (in this example the tunnel was tun0)
1. ifconfig tun0 mtu 1380

*How to tell if you are connected to the VPN over IPv6

-->

Applies to: Windows Server (Semi-Annual Channel), Windows Server 2016, Windows Server 2012 R2, Windows 10

• Previous: Step 5. Configure DNS and Firewall Settings
  

In this step, you'll learn about the ProfileXML options and schema, and configure the Windows 10 client computers to communicate with that infrastructure with a VPN connection.

You can configure the Always On VPN client through PowerShell, Microsoft Endpoint Configuration Manager, or Intune. All three require an XML VPN profile to configure the appropriate VPN settings. Automating PowerShell enrollment for organizations without Configuration Manager or Intune is possible.

Note

Group Policy does not include administrative templates to configure the Windows 10 Remote Access Always On VPN client. However, you can use logon scripts.

ProfileXML overview

ProfileXML is a URI node within the VPNv2 CSP. Rather than configuring each VPNv2 CSP node individually—such as triggers, route lists, and authentication protocols—use this node to configure a Windows 10 VPN client by delivering all the settings as a single XML block to a single CSP node. The ProfileXML schema matches the schema of the VPNv2 CSP nodes almost identically, but some terms are slightly different.

You use ProfileXML in all the delivery methods this deployment describes, including Windows PowerShell, Microsoft Endpoint Configuration Manager, and Intune. There are two ways to configure the ProfileXML VPNv2 CSP node in this deployment:

• OMA-DM. One way is to use an MDM provider using OMA-DM, as discussed earlier in the section VPNv2 CSP nodes. Using this method, you can easily insert the VPN profile configuration XML markup into the ProfileXML CSP node when using Intune.

• Windows Management Instrumentation (WMI)-to-CSP bridge. The second method of configuring the ProfileXML CSP node is to use the WMI-to-CSP bridge—a WMI class called MDM_VPNv2_01—that can access the VPNv2 CSP and the ProfileXML node. When you create a new instance of that WMI class, WMI uses the CSP to create the VPN profile when using Windows PowerShell and Configuration Manager.

Even though these configuration methods differ, both require a properly formatted XML VPN profile. To use the ProfileXML VPNv2 CSP setting, you construct XML by using the ProfileXML schema to configure the tags necessary for the simple deployment scenario. For more information, see ProfileXML XSD.

Below you find each of the required settings and its corresponding ProfileXML tag. You configure each setting in a specific tag within the ProfileXML schema, and not all of them are found under the native profile. For additional tag placement, see the ProfileXML schema.

Important

Any other combination of upper or lower case for 'true' in the following tags results in a partial configuration of the VPN profile:

<AlwaysOn>true</AlwaysOn>
<RememberCredentials>true</RememberCredentials>

Connection type: Native IKEv2

ProfileXML element:

Routing: Split tunneling

ProfileXML element:

Name resolution: Domain Name Information List and DNS suffix

ProfileXML elements:

Triggering: Always On and Trusted Network Detection

ProfileXML elements:

Authentication: PEAP-TLS with TPM-protected user certificates

ProfileXML elements:

You can use simple tags to configure some VPN authentication mechanisms. However, EAP and PEAP are more involved. The easiest way to create the XML markup is to configure a VPN client with its EAP settings, and then export that configuration to XML.

For more information about EAP settings, see EAP configuration.

Manually create a template connection profile

In this step, you use Protected Extensible Authentication Protocol (PEAP) to secure communication between the client and the server. Unlike a simple user name and password, this connection requires a unique EAPConfiguration section in the VPN profile to work.

Instead of describing how to create the XML markup from scratch, you use Settings in Windows to create a template VPN profile. After creating the template VPN profile, you use Windows PowerShell to consume the EAPConfiguration portion from that template to create the final ProfileXML that you deploy later in the deployment.

Record NPS certificate settings

Before creating the template, take note the hostname or fully qualified domain name (FQDN) of the NPS server from the server's certificate and the name of the CA that issued the certificate.

Procedure:

1. On your NPS server, open Network Policy Server.

2. In the NPS console, under Policies, click Network Policies.

3. Right-click Virtual Private Network (VPN) Connections, and click Properties.

4. Click the Constraints tab, and click Authentication Methods.

5. In EAP Types, click Microsoft: Protected EAP (PEAP), and click Edit.

6. Record the values for Certificate issued to and Issuer.

   You use these values in the upcoming VPN template configuration. For example, if the server's FQDN is nps01.corp.contoso.com and the hostname is NPS01, the certificate name is based upon the FQDN or DNS name of the server—for example, nps01.corp.contoso.com.

7. Cancel the Edit Protected EAP Properties dialog box.

8. Cancel the Virtual Private Network (VPN) Connections Properties dialog box.

9. Close Network Policy Server.

Note

If you have multiple NPS servers, complete these steps on each one so that the VPN profile can verify each of them should they be used.

Configure the template VPN profile on a domain-joined client computer

Now that you have the necessary information configure the template VPN profile on a domain-joined client computer. The type of user account you use (that is, standard user or administrator) for this part of the process does not matter.

However, if you haven't restarted the computer since configuring certificate autoenrollment, do so before configuring the template VPN connection to ensure you have a usable certificate enrolled on it.

Note

There is no way to manually add any advanced properties of VPN, such as NRPT rules, Always On, Trusted network detection, etc. In the next step, you create a test VPN connection to verify the configuration of the VPN server and that you can establish a VPN connection to the server.

Manually create a single test VPN connection

1. Sign in to a domain-joined client computer as a member of the VPN Users group.

2. On the Start menu, type VPN, and press Enter.

3. In the details pane, click Add a VPN connection.

4. In the VPN Provider list, click Windows (built-in).

5. In Connection Name, type Template.

6. In Server name or address, type the external FQDN of your VPN server (for example, vpn.contoso.com).

7. Click Save.

8. Under Related Settings, click Change adapter options.

9. Right-click Template, and click Properties.

10. On the Security tab, in Type of VPN, click IKEv2.

11. In Data encryption, click Maximum strength encryption.

12. Click Use Extensible Authentication Protocol (EAP); then, in Use Extensible Authentication Protocol (EAP), click Microsoft: Protected EAP (PEAP) (encryption enabled).

13. Click Properties to open the Protected EAP Properties dialog box, and complete the following steps:

    a. In the Connect to these servers box, type the name of the NPS server that you retrieved from the NPS server authentication settings earlier in this section (for example, NPS01).

    Note

    The server name you type must match the name in the certificate. You recovered this name earlier in this section. If the name does not match, the connection will fail, stating that 'The connection was prevented because of a policy configured on your RAS/VPN server.'

    b. Under Trusted Root Certification Authorities, select the root CA that issued the NPS server's certificate (for example, contoso-CA).

    c. In Notifications before connecting, click Don't ask user to authorize new servers or trusted CAs.

    d. In Select Authentication Method, click Smart Card or other certificate, and click Configure. The Smart Card or other Certificate Properties dialog opens.

    e. Click Use a certificate on this computer.

    f. In the Connect to these servers box, enter the name of the NPS server you retrieved from the NPS server authentication settings in the previous steps.

    g. Under Trusted Root Certification Authorities, select the root CA that issued the NPS server's certificate.

    h. Select the Don't prompt user to authorize new servers or trusted certification authorities check box.

    i. Click OK to close the Smart Card or other Certificate Properties dialog box.

    j. Click OK to close the Protected EAP Properties dialog box.

14. Click OK to close the Template Properties dialog box.

15. Close the Network Connections window.

16. In Settings, test the VPN by clicking Template, and clicking Connect.

Important

Make sure that the template VPN connection to your VPN server is successful. Doing so ensures that the EAP settings are correct before you use them in the next example. You must connect at least once before continuing; otherwise, the profile will not contain all the information necessary to connect to the VPN.

Create the ProfileXML configuration files

Before completing this section, make sure you have created and tested the template VPN connection that the section Manually create a template connection profile describes. Testing the VPN connection is necessary to ensure that the profile contains all the information required to connect to the VPN.

The Windows PowerShell script in Listing 1 creates two files on the desktop, both of which contain EAPConfiguration tags based on the template connection profile you created previously:

• VPN_Profile.xml. This file contains the XML markup required to configure the ProfileXML node in the VPNv2 CSP. Use this file with OMA-DM–compatible MDM services, such as Intune.

• VPN_Profile.ps1. This file is a Windows PowerShell script that you can run on client computers to configure the ProfileXML node in the VPNv2 CSP. You can also configure the CSP by deploying this script through Configuration Manager. You cannot run this script in a Remote Desktop session, including a Hyper-V enhanced session.

Important Picture collage maker for mac free download.

The example commands below require Windows 10 Build 1607 or later.

Create VPN_Profile.xml and VPN_Proflie.ps1

1. Sign in to the domain-joined client computer containing the template VPN profile with the same user account that the section Manually create a template connection profile described.

2. Paste Listing 1 into Windows PowerShell integrated scripting environment (ISE), and customize the parameters described in the comments. These are $Template, $ProfileName, $Servers, $DnsSuffix, $DomainName, $TrustedNetwork, and $DNSServers. A full description of each setting is in the comments.

3. Run the script to generate VPN_Profile.xml and VPN_Profile.ps1 on the desktop.

Listing 1. Understanding MakeProfile.ps1

This section explains the example code that you can use to gain an understanding of how to create a VPN Profile, specifically for configuring ProfileXML in the VPNv2 CSP.

After you assemble a script from this example code and run the script, the script generates two files: VPN_Profile.xml and VPN_Profile.ps1. Use VPN_Profile.xml to configure ProfileXML in OMA-DM compliant MDM services, such as Microsoft Intune.

Use the VPN_Profile.ps1 script in Windows PowerShell or Microsoft Endpoint Configuration Manager to configure ProfileXML on the Windows 10 desktop.

Note

To view the full example script, see the section MakeProfile.ps1 Full Script.

Parameters

Configure the following parameters:

$Template. The name of the template from which to retrieve the EAP configuration.

$ProfileName. Unique alphanumeric identifier for the profile. The profile name must not include a forward slash (/). If the profile name has a space or other non-alphanumeric character, it must be properly escaped according to the URL encoding standard.

$Servers. Public or routable IP address or DNS name for the VPN gateway. It can point to the external IP of a gateway or a virtual IP for a server farm. Examples, 208.147.66.130 or vpn.contoso.com.

$DnsSuffix. Specifies one or more commas separated DNS suffixes. The first in the listis also used as the primary connection-specific DNS suffix for the VPN Interface. The entire list will also be added into the SuffixSearchList.

$DomainName. Used to indicate the namespace to which the policy applies. When a Name query is issued, the DNS client compares the name in the query to all of the namespaces under DomainNameInformationList to find a match. This parameter can be one of the following types:

• FQDN - Fully qualified domain name
• Suffix - A domain suffix that will be appended to the shortname query for DNS resolution. To specify a suffix, prepend a period (.) to the DNS suffix.

$DNSServers. List of comma-separated DNS Server IP addresses to use for the namespace.

$TrustedNetwork. Comma-separated string to identify the trusted network. VPN does not connect automatically when the user is on their corporate wireless network where protected resources are directly accessible to the device.

The following are example values for parameters used in the commands below. Ensure that you change these values for your environment.

Prepare and create the profile XML

The following example commands get EAP settings from the template profile:

Create the profile XML

Important

Any other combination of upper or lower case for 'true' in the following tags results in a partial configuration of the VPN profile:

<AlwaysOn>true</AlwaysOn>
<RememberCredentials>true</RememberCredentials>

Output VPN_Profile.xml for Intune

You can use the following example command to save the profile XML file:

Output VPN_Profile.ps1 for the desktop and Configuration Manager

The following example code configures an AlwaysOn IKEv2 VPN Connection by using the ProfileXML node in the VPNv2 CSP.

You can use this script on the Windows 10 desktop or in Configuration Manager.

Define key VPN profile parameters

Escape special characters in the profile

Define WMI-to-CSP Bridge properties

Determine user SID for VPN profile:

Define WMI session:

Detect and delete previous VPN profile:

Create the VPN profile:

Save the profile XML file

MakeProfile.ps1 Full Script

Most examples use the Set-WmiInstance Windows PowerShell cmdlet to insert ProfileXML into a new instance of the MDM_VPNv2_01 WMI class.

However, this does not work in Configuration Manager because you cannot run the package in the end users' context. Therefore, this script uses the Common Information Model to create a WMI session in the user's context, and then it creates a new instance of the MDM_VPNv2_01 WMI class in that session. This WMI class uses the WMI-to-CSP bridge to configure the VPNv2 CSP. Therefore, by adding the class instance, you configure the CSP.

Important

WMI-to-CSP bridge requires local admin rights, by design. To deploy per user VPN profiles you should be using Configuration Manager or MDM.

Note

The script VPN_Profile.ps1 uses the current user's SID to identify the user's context. Because no SID is available in a Remote Desktop session, the script does not work in a Remote Desktop session. Likewise, it does not work in a Hyper-V enhanced session. If you're testing a Remote Access Always On VPN in virtual machines, disable enhanced session on your client VMs before running this script.

The following example script includes all of the code examples from previous sections. Ensure that you change example values to values that are appropriate for your environment.

Configure the VPN client by using Windows PowerShell

To configure the VPNv2 CSP on a Windows 10 client computer, run the VPN_Profile.ps1 Windows PowerShell script that you created in the Create the profile XML section. Open Windows PowerShell as an Administrator; otherwise, you'll receive an error saying, Access denied.

After running VPN_Profile.ps1 to configure the VPN profile, you can verify at any time that it was successful by running the following command in the Windows PowerShell ISE:

Successful results from the Get-WmiObject cmdlet

The ProfileXML configuration must be correct in structure, spelling, configuration, and sometimes letter case. If you see something different in structure to Listing 1, the ProfileXML markup likely contains an error.

If you need to troubleshoot the markup, it is easier to put it in an XML editor than to troubleshoot it in the Windows PowerShell ISE. In either case, start with the simplest version of the profile, and add components back one at a time until the issue occurs again.

Configure the VPN client by using Configuration Manager

Always On Vpn Cisco Anyconnect

In Configuration Manager, you can deploy VPN profiles by using the ProfileXML CSP node, just like you did in Windows PowerShell. Here, you use the VPN_Profile.ps1 Windows PowerShell script that you created in the section Create the ProfileXML configuration files.

To use Configuration Manager to deploy a Remote Access Always On VPN profile to Windows 10 client computers, you must start by creating a group of machines or users to whom you deploy the profile. In this scenario, create a user group to deploy the configuration script.

Create a user group

1. In the Configuration Manager console, open Assets and ComplianceUser Collections.

2. On the Home ribbon, in the Create group, click Create User Collection.

3. On the General page, complete the following steps:

   a. In Name, type VPN Users.

   b. Click Browse, click All Users and click OK.

   c. Click Next.

4. On the Membership Rules page, complete the following steps:

   a. In Membership rules, click Add Rule, and click Direct Rule. In this example, you're adding individual users to the user collection. However, you might use a query rule to add users to this collection dynamically for a larger-scale deployment.

   b. On the Welcome page, click Next.

   c. On the Search for Resources page, in Value, type the name of the user you want to add. The resource name includes the user's domain. To include results based on a partial match, insert the % character at either end of your search criterion. For example, to find all users containing the string 'lori,' type %lori%. Click Next.

   d. On the Select Resources page, select the users you want to add to the group, and click Next.

   e. On the Summary page, click Next.

   f. On the Completion page, click Close.

5. Back on the Membership Rules page of the Create User Collection Wizard, click Next.

6. On the Summary page, click Next.

7. On the Completion page, click Close.

After you create the user group to receive the VPN profile, you can create a package and program to deploy the Windows PowerShell configuration script that you created in the section Create the ProfileXML configuration files.

Create a package containing the ProfileXML configuration script

1. Host the script VPN_Profile.ps1 on a network share that the site server computer account can access.

2. In the Configuration Manager console, open Software LibraryApplication ManagementPackages.

3. On the Home ribbon, in the Create group, click Create Package to start the Create Package and Program Wizard.

4. On the Package page, complete the following steps:

   a. In Name, type Windows 10 Always On VPN Profile.

   b. Select the This package contains source files check box, and click Browse.

   c. In the Set Source Folder dialog box, click Browse, select the file share containing VPN_Profile.ps1, and click OK.Make sure you select a network path, not a local path. In other words, the path should be something like fileservervpnscript, not c:vpnscript.

5. Click Next.

6. On the Program Type page, click Next.

7. On the Standard Program page, complete the following steps:

   a. In Name, type VPN Profile Script.

   b. In Command line, type PowerShell.exe -ExecutionPolicy Bypass -File 'VPN_Profile.ps1'.

   c. In Run mode, click Run with administrative rights.

   d. Click Next.

8. On the Requirements page, complete the following steps:

   a. Select This program can run only on specified platforms.

   b. Select the All Windows 10 (32-bit) and All Windows 10 (64-bit) check boxes.

   c. In Estimated disk space, type 1.

   d. In Maximum allowed run time (minutes), type 15.

   e. Click Next.

9. On the Summary page, click Next.

10. On the Completion page, click Close.

With the package and program created, you need to deploy it to the VPN Users group.

Deploy the ProfileXML configuration script

1. In the Configuration Manager console, open Software LibraryApplication ManagementPackages.

2. In Packages, click Windows 10 Always On VPN Profile.

3. On the Programs tab, at the bottom of the details pane, right-click VPN Profile Script, click Properties, and complete the following steps:

   a. On the Advanced tab, in When this program is assigned to a computer, click Once for every user who logs on.

   b. Click OK.

4. Right-click VPN Profile Script and click Deploy to start the Deploy Software Wizard.

5. On the General page, complete the following steps:

   a. Beside Collection, click Browse.

   b. In the Collection Types list (top left), click User Collections.

   c. Click VPN Users, and click OK.

   d. Click Next.

6. On the Content page, complete the following steps:

   a. Click Add, and click Distribution Point.

   b. In Available distribution points, select the distribution points to which you want to distribute the ProfileXML configuration script, and click OK.

   c. Click Next.

7. On the Deployment settings page, click Next.

8. On the Scheduling page, complete the following steps:

   a. Click New to open the Assignment Schedule dialog box.

   b. Click Assign immediately after this event, and click OK.

   c. Click Next.

9. On the User Experience page, complete the following steps:

   1. Select the Software Installation check box.

   2. Click Summary.

10. On the Summary page, click Next.

11. On the Completion page, click Close.

With the ProfileXML configuration script deployed, sign in to a Windows 10 client computer with the user account you selected when you built the user collection. Verify the configuration of the VPN client.

Note

The script VPN_Profile.ps1 does not work in a Remote Desktop session. Likewise, it does not work in a Hyper-V enhanced session. If you're testing a Remote Access Always On VPN in virtual machines, disable enhanced session on your client VMs before continuing.

Verify the configuration of the VPN client

1. In Control Panel, under SystemSecurity, click Configuration Manager.

2. In the Configuration Manager Properties dialog, on the Actions tab, complete the following steps:

   a. Click Machine Policy Retrieval & Evaluation Cycle, click Run Now, and click OK.

   b. Click User Policy Retrieval & Evaluation Cycle, click Run Now, and click OK.

   c. Click OK.

3. Close the Control Panel.

You should see the new VPN profile shortly.

Configure the VPN client by using Intune

To use Intune to deploy Windows 10 Remote Access Always On VPN profiles, you can configure the ProfileXML CSP node by using the VPN profile you created in the section Create the ProfileXML configuration files, or you can use the base EAP XML sample provided below.

Note

Intune now uses Azure AD groups. If Azure AD Connect synced the VPN Users group from on-premises to Azure AD, and users are assigned to the VPN Users group, you are ready to proceed.

Create the VPN device configuration policy to configure the Windows 10 client computers for all users added to the group. Since the Intune template provides VPN parameters, only copy the <EapHostConfig> </EapHostConfig> portion of the VPN_ProfileXML file.

Create the Always On VPN configuration policy

1. Sign into the Azure portal.

2. Go to Intune > Device Configuration > Profiles.

3. Click Create Profile to start the Create profile Wizard.

4. Enter a Name for the VPN profile and (optionally) a description.

5. Under Platform, select Windows 10 or later, and choose VPN from the Profile type drop-down.

   Tip

   If you are creating a custom VPN profileXML, see Apply ProfileXML using Intune for the instructions.

6. Under the Base VPN tab, verify or set the following settings:

   • Connection name: Enter the name of the VPN connection as it appears on the client computer in the VPN tab under Settings, for example, Contoso AutoVPN.

   • Servers: Add one or more VPN servers by clicking Add.

   • Description and IP Address or FQDN: Enter the description and IP Address or FQDN of the VPN server. These values must align with the Subject Name in the VPN server's authentication certificate.

   • Default server: If this is the default VPN server, set to True. Doing this enables this server as the default server that devices use to establish the connection.

   • Connection type: Set to IKEv2.

   • Always On: Set to Enable to connect to the VPN automatically at the sign-in and stay connected until the user manually disconnects.

   • Remember credentials at each logon: Boolean value (true or false) for caching credentials. If set to true, credentials are cached whenever possible.

7. Copy the following XML string to a text editor:

   Important

   Any other combination of upper or lower case for 'true' in the following tags results in a partial configuration of the VPN profile:

   <AlwaysOn>true</AlwaysOn>
   <RememberCredentials>true</RememberCredentials>

8. Replace the <TrustedRootCA>5a 89 fe cb 5b 49 a7 0b 1a 52 63 b7 35 ee d7 1c c2 68 be 4b</TrustedRootCA> in the sample with the certificate thumbprint of your on-premises root certificate authority in both places.

   Important

   Do not use the sample thumbprint in the <TrustedRootCA></TrustedRootCA> section below. The TrustedRootCA must be the certificate thumbprint of the on-premises root certificate authority that issued the server-authentication certificate for RRAS and NPS servers. This must not be the cloud root certificate, nor the intermediate issuing CA certificate thumbprint.

9. Replace the <ServerNames>NPS.contoso.com</ServerNames> in the sample XML with the FQDN of the domain-joined NPS where authentication takes place.

10. Copy the revised XML string and paste into the EAP Xml box under the Base VPN tab and click OK.An Always On VPN Device Configuration policy using EAP is created in Intune.

Sync the Always On VPN configuration policy with Intune

Cisco Asa Always On Vpn

To test the configuration policy, sign in to a Windows 10 client computer as the user you added to the Always On VPN Users group, and then sync with Intune.

1. On the Start menu, click Settings.

2. In Settings, click Accounts, and click Access work or school.

3. Click the MDM profile, and click Info.

4. Click Sync to force an Intune policy evaluation and retrieval.

5. Close Settings. After synchronization, you see the VPN profile available on the computer.

Next steps

You are done deploying Always On VPN. For other features you can configure, see the table below:

Vpn Anyconnect Download

If you want to..	Then see..
Configure Conditional Access for VPN	Step 7. (Optional) Configure conditional access for VPN connectivity using Azure AD: In this step, you can fine-tune how authorized VPN users access your resources using Azure Active Directory (Azure AD) conditional access. With Azure AD conditional access for virtual private network (VPN) connectivity, you can help protect the VPN connections. Conditional Access is a policy-based evaluation engine that lets you create access rules for any Azure Active Directory (Azure AD) connected application.
Learn more about the advanced VPN features	Advanced VPN Features: This page provides guidance on how to enable VPN Traffic Filters, how to configure Automatic VPN connections using App-Triggers, and how to configure NPS to only allow VPN Connections from clients using certificates issued by Azure AD.